Toll Free: 866.896.2944

Product Manual

BAT CDCMA
SKU: IPD-BAT-CDMA

Cellular & Internet
Alarm Communicator

Quick Reference

Programming on GE Network:

Device 0

Cellular BAT-CDMA as Sole Communicator

Location 0

Enter the Phone Number

Device 0:
Location 0

Cellular BAT-CDMA as Sole Communicator:
Enter the Phone Number

Location 1

Enter Account Number

Device 0:
Location 1

Cellular BAT-CDMA as Sole Communicator:
Enter Account Number

Location 2

Enter ‘13’ for Contact ID

Device 0:
Location 2

Cellular BAT-CDMA as Sole Communicator:
Enter ‘13’ for Contact ID

Programming on Vista:

Section

Cellular BAT-CDMA as Sole Communicator

*41

Enter the Phone Number

Section:
*41

Cellular BAT-CDMA as Sole Communicator:
Enter the Phone Number

*43

Enter Account Number

Section:
*43

Cellular BAT-CDMA as Sole Communicator:
Enter Account Number

*193

Enter 1, 0. Enable to turn on Address 20

Section:
*193

Cellular BAT-CDMA as Sole Communicator:
Enter 1, 0. Enable to turn on Address 20

Programming on Vista:

Section

Cellular BAT-CDMA as Sole Communicator

301

Enter the Phone Number

Section:
301

Cellular BAT-CDMA as Sole Communicator:
Enter the Phone Number

310

Enter Account Number

Section:
310

Cellular BAT-CDMA as Sole Communicator:
Enter Account Number

350

Enter ‘03’ for Contact ID

Section:
350

Cellular BAT-CDMA as Sole Communicator:
Enter ‘03’ for Contact ID

Technical Support Information

For Technical Support, call toll free: 866-896-2944
Monday - Friday 7a - 6:30p CST
techsupport@ipdatatel.com
ipdatatel.com
www.alarmdealer.com
setup.alarmdealer.com - used to view device information

ipDatatel, LLC
13110 Southwest Freeway
Sugar Land, TX 77478
Toll Free: 866-896-2944

Getting Started

Pre-Installation

Hardware Registration

Before installation of your Cellular BAT-CDMA, it must be registered at www.alarmdealer.com.

Here are the steps needed to register your hardware:

  • Log in to alarmdealer.com with the dealer login information that was emailed to you.
  • Click Create Account Wizard
  • Follow the 4-Step Wizard

Installation Guide

Cellular BAT (CDMA) Service Provisioning

All new Cellular BAT’s are pre-provisioned with Verizon, which means they are linked to the network and no additional steps are required for this Product to come online.

Re-Provisioning (If necessary)

If you are installing a Cellular CAT that was previously installed, you may need to perform a re- provisioning of the OTAP, which is required by Verizon to make the Product come online. If a Cellular CAT is removed or deactivated from an account, you will need to make sure it is re-provision. To re- provision the Cellular CAT, please follow these steps:

Service Provisioning Steps

1. To begin, ensure that the board is powered appropriately with 12Volts either from a battery or the Customer Control Panel.
2. Press and release the SW1 switch 3 times (I.E. triple click the switch)
3. Once released, the unit will auto power cycle. When it re- initializes you should see LEDs 3 – 6 scrolling
4. Once acquired into the network, you will see the signal strength indicated on the board via LEDs 3 – 6.
5. Wait approximately 5 minutes before sending signals.

General Considerations

  • Before installation, your Cellular BAT-CDMA must also be setup using the dealer Branded Portal www.alarmdealer.com.
  • The Product should be installed securely in the supplied plastic housing, and be mounted next to your alarm control panel.
  • Where available, proximity to the hard-wired Ethernet Internet connection should be taken into consideration when routing wires.
  • Choose a location with good Cellular reception by monitoring the Product’s signal strength LEDs with a pre-wire power up.
  • The Product must be completely powered down before starting the wire up.
  • Programming is simple using the alarm control panel.

Locating and Installing the Cellular BAT-CDMA

The Product connects to the alarm panel’s power connections, Telco, virtual keypad bus (if available), and keyswitch connections (optional).
The Cellular BAT-CDMA should be connected to the Internet via a hard-wired (RJ45) internet connection located on the lower-right hand side to the circuit board. If a hard-wired Internet connection is not available then the Cellular connection will be used. The Product automatically seeks an IP address. There is no need to program routers or switches.

Telco - Digital Dialer

The Cellular BAT-CDMA‘s signal collection expects Contact ID format from the digital dialer on the alarm panel. Most control panels made in the last decade are capable of this. Wire the Telco side of the alarm control’s Tip & Ring to the Product’s Tip & Ring.

Virtual Keypad Connection

The Cellular BAT-CDMA connects to most panels as a virtual keypad, allowing the customer full virtual keypad access after they have authenticated using their username and password you have assigned them in the pre-installation phase. This allows the customer to use our SecureSmart mobile phone and web interfaces. You will need to refer to the wiring diagram for your specific panel because the panel side of he virtual keypad connection has various labels such as: Data in-Data out, YEL-GRN, or just Data. This connects to the G/RX, Y/TX connections on the Product.

Power Connection

The last step is to wire the alarm panel’s 12VDC auxiliary power and ground to Product’s positive (pin 3) and negative (pin 4) terminals.

Basic Programming

Because the Cellular BAT-CDMA simulates telephone service to the panel, general programming for the control is limited to configuring the signal format as Contact ID. This also inputs a telephone number to dial. In our case the actual telephone number does NOT matter and is NOT used in the signal delivery process.

Full Virtual Keypad Programming

For panels that are “Interactive Ready” (See Supported Panels section page 23) the following programming will give you full virtual keypad access to where the customer can enter their 4 digit code to arm & disarm the system, when using SecureSmart mobile and web interfaces.

DSC Panels:
No programming required to make the virtual keypad operate.

GE Panels:
Enter & Exit programming twice, Cellular BAT-CDMA will enroll as a Keypad (240) in the panel.

Honeywell Vista Panels:
Enable *193 with (1,0) to turn on Address 20. (Additional keypad will not be able to share Address 20)

Troubleshooting Diagnostic Information

Under normal operation the Activity light will periodically blink. A power cycle is recommended if the Activity light is not periodically blinking.

LED – 1: Status LED

  • Flashing - Offline.
  • Solid – Communicating with Verizon, Online.
  • OFF (No Flashing) - Online Via Ethernet or WIFI

LED – 2: Activity LED:

Used to indicate signal transmission

LEDs – 3 to 6:

Verizon Signal Strength. LED 3 being the lowest and LED 6 being the highest signal strength. The minimum recommended operation is two bars (LEDs 3 & 4 Solid).

Validating the Installation

After the unit is properly connected to the Alarm Panel and powered up, use the following steps to validate that the system is functioning properly:

  • Ensure that virtual keypad functionality works through alarmdealer.com, or the SecureSmart mobile app.
  • Ensure that alarm signals reach your central station.

Wiring & Programming for Popular Panels

The following pages are organized by Alarm Panel type. Wiring and programming instructions are given for:

  • Digital Security Control (DSC) Alarm Panels
  • Ademco & Honeywell Vista Alarm Panels
  • GE NetworX Alarm Panels

DSC Panel Wiring and Programming

TELCO Programming:

General Concept Programming on DSC (Cellular BAT-CDMA as Sole Communicator):

Section

As Sole Communicator

Code Summarization

301

Enter a Receiver Number

Section:
301

As Sole Communicator:
Enter a Receiver Number

310

Enter Account Number

Section:
310

As Sole Communicator:
Enter Account Number

350

Enter ‘03’ to send Contact ID

Panel default is ‘04’, SIA

Section:
350

As Sole Communicator:
Enter ‘03’ to send Contact ID

Code Summarization:
Panel default is ‘04’, SIA

Note: Ensure All Report Codes are in, and signals can be sent.

DSC PC-Link Connection

This allows for remote downloader functionality with ipDatatel’s Universal Downloader (uDownloader) software. (Not Required)

DSC Panel Programming

See Supported Panels section on page 23. Perform the TELCO Programming if Tip & Ring is being used. If for whatever reason you cannot use Tip & Ring to send Signals then you can wire a PC-Link from the Product to the Panel and perform PC-Link Programming. Otherwise, ALWAYS use TELCO Programming.

PC-Link Programming:

DSC Programming for Communications - GSM Emulation: If GSM is used, it must be in dialer capture mode.

Section

Cellular BAT as Sole
Communicator

Cellular BAT as Fail over w/Add’l Communication Device

Cellular BAT as Dual Reporting w/Add’l Communication Device

Code Summarization

015

Disable Option 7

If GSM: Disable Option 7 If Phone Line, Enable Option 7

If GSM: Disable Option 7 If Phone Line, Enable Option 7

Option 7 turns on/off telephone line supervision.

Section:
015

Cellular BAT as Sole Communicator:
Disable Option 7

Cellular BAT as Fail over w/Add’l Communication Device:
If GSM: Disable Option 7 If Phone Line, Enable Option 7

Cellular BAT as Dual Reporting w/Add’l Communication Device:
If GSM: Disable Option 7 If Phone Line, Enable Option 7

Code Summarization:
Option 7 turns on/off telephone line supervision.

167

Set ‘060’ Seconds

Set ‘060’ Seconds

Set ‘060’ Seconds

Sets T-Link acknowledgment delay to 60 secs.

Section:
167

Cellular BAT as Sole Communicator:
Set ‘060’ Seconds

Cellular BAT as Fail over w/Add’l Communication Device:
Set ‘060’ Seconds

Cellular BAT as Dual Reporting w/Add’l Communication Device:
Set ‘060’ Seconds

Code Summarization:
Sets T-Link acknowledgment delay to 60 secs.

301

Set ‘CAAF’

Set ‘CAAF’

Set ‘CAAF’

‘CAAF’ has to be set for the panel to send signals to the PC- Link

Section:
301

Cellular BAT as Sole
Communicator:

Set ‘CAAF’

Cellular BAT as Fail over w/Add’l Communication Device:
Set ‘CAAF’

Cellular BAT as Dual Reporting w/Add’l Communication Device:
Set ‘CAAF’

Code Summarization:
‘CAAF’ has to be set for the panel to send signals to the PC- Link

302

N/A

N/A

Set ‘Central Station Receiver #’

Second telephone number goes here.

Section:
302

Cellular BAT as Sole Communicator:
N/A

Cellular BAT as Fail over w/Add’l Communication Device:

Cellular BAT as Dual Reporting w/Add’l Communication Device:
Set ‘Central Station Receiver #’

Code Summarization:
Second telephone number goes here.

303

N/A

Set ‘Central Station Receiver #’

Set ‘Central Station Receiver #’

This section is the telephone backup of section 301.

Section:
303

Cellular BAT as Sole Communicator:
N/A

Cellular BAT as Fail over w/Add’l Communication Device:
Set ‘Central Station Receiver #’

Cellular BAT as Dual Reporting w/Add’l Communication Device:
Set ‘Central Station Receiver #’

Code Summarization:
This section is the telephone backup of section 301.

350

Set ‘04’/‘04’

Set ‘04’/’03 for Contact ID, 04 for SIA FSK’ **

Set ‘04’/’03 for Contact ID, 04 for SIA FSK’ **

Format sent as either contact ID (03), or SIA FSK (04). The PC-Link/BAT can ONLY receive signals via SIA FSK (04).

Section:
350

Cellular BAT as Sole
Communicator:

Set ‘04’/‘04’

Cellular BAT as Fail over w/Add’l Communication Device:
Set ‘04’/’03 for Contact ID, 04 for SIA FSK’ **

Cellular BAT as Dual Reporting w/Add’l Communication Device:
Set ‘04’/’03 for Contact ID, 04 for SIA FSK’ **

Code Summarization:
Format sent as either contact ID (03), or SIA FSK (04). The PC-Link/BAT can ONLY receive signals via SIA FSK (04).

351

Enable Option 1

Enable Option 1, 5

Enable Option 1, 2, 5

Options to turn on/off alarm/restore for telephone 1 (option 1), telephone 2 (option 2), and alternate communications (option 5).

Section:
351

Cellular BAT as Sole
Communicator:

Enable Option 1

Cellular BAT as Fail over w/Add’l Communication Device:
Enable Option 1, 5

Cellular BAT as Dual Reporting w/Add’l Communication Device:
Enable Option 1, 2, 5

Code Summarization:
Options to turn on/off alarm/restore for telephone 1 (option 1), telephone 2 (option 2), and alternate communications (option 5).

359

Enable Option 1

Enable Option 1, 5

Enable Option 1, 2, 5

Options to turn on/off tamper/restore for telephone 1 (option 1), telephone 2 (option 2), and alternate communications (option 5).

Section:
359

Cellular BAT as Sole
Communicator:

Enable Option 1

Cellular BAT as Fail over w/Add’l Communication Device:
Enable Option 1, 5

Cellular BAT as Dual Reporting w/Add’l Communication Device:
Enable Option 1, 2, 5

Code Summarization:
Options to turn on/off tamper/restore for telephone 1 (option 1), telephone 2 (option 2), and alternate communications (option 5).

367

Enable Option 1

Enable Option 1, 5

Enable Option 1, 2, 5

Options to turn on/off opening/closing for telephone 1 (option 1),telephone 2 (option 2), and alternate communications (option 5)

Section:
367

Cellular BAT as Sole
Communicator:

Enable Option 1

Cellular BAT as Fail over w/Add’l Communication Device:
Enable Option 1, 5

Cellular BAT as Dual Reporting w/Add’l Communication Device:
Enable Option 1, 2, 5

Code Summarization:
Options to turn on/off opening/closing for telephone 1 (option 1),telephone 2 (option 2), and alternate communications (option 5)

375

Enable Option 1

Enable Option 1, 5

Enable Option 1, 2, 5

Options to turn on/off maintenance for telephone 1 (option 1), telephone 2 (option 2), and alternate communications (option 5)

Section:
375

Cellular BAT as Sole Communicator:
Enable Option 1

Cellular BAT as Fail over w/Add’l Communication Device:
Enable Option 1, 5

Cellular BAT as Dual Reporting w/Add’l Communication Device:
Enable Option 1, 2, 5

Code Summarization:
Options to turn on/off maintenance for telephone 1 (option 1), telephone 2 (option 2), and alternate communications (option 5)

376

Enable Option 1

Enable Option 1, 5

Enable Option 1, 2, 5

Options to turn on/off testing for telephone 1 (option 1), telephone 2 (option 2), and alternate communications (option 5)

Section:
376

Cellular BAT as Sole Communicator:
Enable Option 1

Cellular BAT as Fail over w/Add’l Communication Device:
Enable Option 1, 5

Cellular BAT as Dual Reporting w/Add’l Communication Device:
Enable Option 1, 2, 5

Code Summarization:
Options to turn on/off testing for telephone 1 (option 1), telephone 2 (option 2), and alternate communications (option 5)

380

Enable Option 1

Enable Option 1, 5

Enable Option 1, 5

Option 1 turns on/off communications. Option 5 turns on/off 3rd phone number.

Section:
380

Cellular BAT as Sole Communicator:
Enable Option 1

Cellular BAT as Fail over w/Add’l Communication Device:
Enable Option 1, 5

Cellular BAT as Dual Reporting w/Add’l Communication Device:
Enable Option 1, 5

Code Summarization:
Option 1 turns on/off communications. Option 5 turns on/off 3rd phone number.

381

Disable Option 3, Enable Option 5

Disable Option 3, Enable Option 5, 6

Disable Option 3, Enable Option 5, 6

Option 3 turns on/off code reporting. Options 5 & 6 turns on/off communication with phone lines 1/3 & 2 respectively.

Section:
381

Cellular BAT as Sole Communicator:
Disable Option 3, Enable Option 5

Cellular BAT as Fail over w/Add’l Communication Device:
Disable Option 3, Enable Option 5, 6

Cellular BAT as Dual Reporting w/Add’l Communication Device:
Disable Option 3, Enable Option 5, 6

Code Summarization:
Option 3 turns on/off code reporting. Options 5 & 6 turns on/off communication with phone lines 1/3 & 2 respectively.

382

Enable Option 5

Enable Option 5

Enable Option 5

Option 5 enables/disables T-Link/PC-Link.

Section:
382

Cellular BAT as Sole
Communicator:

Enable Option 5

Cellular BAT as Fail over w/Add’l Communication Device:
Enable Option 5

Cellular BAT as Dual Reporting w/Add’l Communication Device:
Enable Option 5

Code Summarization:
Option 5 enables/disables T-Link/PC-Link.

389

Set ‘003’ Seconds

Set ‘003’ Seconds

Set ‘003’ Seconds

The time it will take to periodically check for faults on the T-Link/PC- Link.

Section:
389

Cellular BAT as Sole
Communicator:

Set ‘003’ Seconds

Cellular BAT as Fail over w/Add’l Communication Device:
Set ‘003’ Seconds

Cellular BAT as Dual Reporting w/Add’l Communication Device:
Set ‘003’ Seconds

Code Summarization:
The time it will take to periodically check for faults on the T-Link/PC- Link.

Honeywell Vista Panel Wiring and Programming

Honeywell Vista Panel Programming

See Supported Panels section on page 23. Perform the TELCO Programming if Tip & Ring is being used. If for whatever reason you cannot use Tip & Ring to send Signals then you can perform ECP Bus Programming. Otherwise, ALWAYS use TELCO Programming.

TELCO Programming:

Programming on Vista (BAT as Sole Communicator):

Section

Cellular BAT as Sole Communicator

Code Summarization

*41

Enter Phone Number

Section:
*41

Cellular BAT as Sole Communicator:
Enter Phone Number

*43

Enter Account Number

Section:
*43

Cellular BAT as Sole Communicator:
Enter Account Number

*49

Enter 5

For All Communications to BAT

Section:
*49

Cellular BAT as Sole Communicator:
Enter 5

Code Summarization:
For All Communications to BAT

*54

Enter 0

No Delay Between Communicators

Section:
*54

Cellular BAT as Sole Communicator:
Enter 0

Code Summarization:
No Delay Between Communicators

*55

Enter 0

Phone Line Communicates First

Section:
*55

Cellular BAT as Sole Communicator:
Enter 0

Code Summarization:
Phone Line Communicates First

*65 & *66

Enter 1

If you want Opening/Closing Reports

Section:
*65 & *66

Cellular BAT as Sole Communicator:
Enter 1

Code Summarization:
If you want Opening/Closing Reports

*193

Enter 1, 0

Enable to turn on Address 20

Section:
*193

Cellular BAT as Sole Communicator:
Enter 1, 0

Code Summarization:
Enable to turn on Address 20

ECP Bus Programming:

Vista Programming for Communications - GSM Emulation:

Section

Cellular BAT as Sole Communicator

Cellular BAT in use with another Communication Device for Failover

For Dual Reporting

Code Summarization

*29

Enter 1

Enter 1

Enter 1

This enables GSM. The BAT Emulates a GSM.

Section:
*29

Cellular BAT as Sole Communicator:
Enter 1

Cellular BAT in use with another Communication Device for Failover:
Enter 1

For Dual Reporting:
Enter 1

Code Summarization:
This enables GSM. The BAT Emulates a GSM.

*42

N/A

Enter Central Station Receiver Number

Enter Central Station Receiver Number

Secondary Phone Number

Section:
*42

Cellular BAT as Sole Communicator:
N/A

Cellular BAT in use with another Communication Device for Failover:
Enter Central Station Receiver Number

For Dual Reporting:
Enter Central Station Receiver Number

Code Summarization:
Secondary Phone Number

*43

Enter Account Number

Enter Account Number

Enter Account Number

This is the central station account number

Section:
*43

Cellular BAT as Sole Communicator:
Enter Account Number

Cellular BAT in use with another Communication Device for Failover:
Enter Account Number

For Dual Reporting:
Enter Account Number

Code Summarization:
This is the central station account number

*49

Enter 5

Please refer to panel manual for your particular application requirements

Please refer to panel manual for your particular application requirements

Dual Reporting; Setting to 5 sends all reporting to both primary and secondary.

Section:
*49

Cellular BAT as Sole Communicator:
Enter 5

Cellular BAT in use with another Communication Device for Failover:
Please refer to panel manual for your particular application requirements

For Dual Reporting:
Please refer to panel manual for your particular application requirements

Code Summarization:
Dual Reporting; Setting to 5 sends all reporting to both primary and secondary.

*54

Enter 0

Enter 2

Enter 0

The time it takes for the communicator to switch from primary to secondary.

Section:
*54

Cellular BAT as Sole Communicator:
Enter 0

Cellular BAT in use with another Communication Device for Failover:
Enter 2

For Dual Reporting:
Enter 0

Code Summarization:
The time it takes for the communicator to switch from primary to secondary.

*55

Enter 1

Enter 1

Enter 1 (BAT is Primary Communicator)

Setting to 1 gives signal priority to GSM (BAT).

Section:
*55

Cellular BAT as Sole Communicator:
Enter 1

Cellular BAT in use with another Communication Device for Failover:
Enter 1

For Dual Reporting:
Enter 1 (BAT is Primary Communicator)

Code Summarization:
Setting to 1 gives signal priority to GSM (BAT).

*65

Enter 1

Enter 1

Enter 1

Report Code for Openings.

Section:
*65

Cellular BAT as Sole Communicator:
Enter 1

Cellular BAT in use with another Communication Device for Failover:
Enter 1

For Dual Reporting:
Enter 1

Code Summarization:
Report Code for Openings.

*66

Enter 1, 1

Enter 1, 1

Enter 1, 1

Report Code for Arming in Away and Stay.

Section:
*66

Cellular BAT as Sole Communicator:
Enter 1, 1

Cellular BAT in use with another Communication Device for Failover:
Enter 1, 1

For Dual Reporting:
Enter 1, 1

Code Summarization:
Report Code for Arming in Away and Stay.

*193

Enter 1, 0

Enter 1, 0

Enter 1, 0

1 turns on/off keypad address. 0 sets sound to beep.

Section:
*193

Cellular BAT as Sole Communicator:
Enter 1, 0

Cellular BAT in use with another Communication Device for Failover:
Enter 1, 0

For Dual Reporting:
Enter 1, 0

Code Summarization:
1 turns on/off keypad address. 0 sets sound to beep.

See Supported Panels below to verify your panel’s revision number and GSM emulation programming.

GE Panel Wiring and Programming

GE Panel Programming

Recommended:
General Concept Programming on GE NetworX:

Section

BAT as Sole Communicator

Code Summarization

Device 0, Location 0

Enter the Phone Number

Section:
Device 0, Location 0

BAT as Sole Communicator:
Enter the Phone Number

Device 0, Location 1

Enter Account Number

Section:
Device 0, Location 1

BAT as Sole Communicator:
Enter Account Number

Device 0, Location 2

Enter ‘13’ Recommended value

Contact ID

Section:
Device 0, Location 2

BAT as Sole Communicator:
Enter ‘13’ Recommended value

Code Summarization:
Contact ID

Programming for Communications (GSM Emulation):

As with existing devices in the NetworX family, the BAT is automatically enrolled with the control panel when the panel exits programming mode.

The Cellular BAT-CDMA registers as a keypad and a communications device on addresses 240 and 76, respectively. All signals are read directly from the panel memory, so any call directions and/or reporting codes programmed are specifically for other communication devices, such as the panel dialer.

For Central Station monitoring, the Account Number for the customer MUST be entered into alarmdealer.com. If this is not done, all alarm signals sent to the Central Station will arrive with an incorrect account number attached. The Cellular BAT-CDMA must be power-cycled after making this change.

To have this enabled so the Cellular BAT-CDMA gets signals from the keybus, you must contact ipDatatel. Otherwise use the TELCO to send signals.

Generic Alarm Panel Wiring and Programming

Generic Alarm Panel Programming

  • Program the panel Phone Number into the panel
  • Program the Customer Account Number into the panel
  • Program Reporting codes into the panel
  • Program panel to transmit in Contact ID format

Generic Keyswitch Wiring and Programming

For basic keyswitch interactive services with the Cellular BAT- CDMA, the following alarm panel wiring is needed.

  • A programmable output on the alarm panel will be used to signal to the Product (Y/Tx terminal) that the panel has entered Arm/Disarmed State.
  • The Z1 output on the Product will be used as a key switch connecting to a ‘zone’ terminal on the alarm panel.

*Panel zone resistor placed on Terminal 3 to 5 to determine correct arm and disarm state.

Generic Keyswitch Programming

Keyswitch state programming examples for Ademco, Digital Security Controls, and GE NetworX for Keyswitch and panel state program output operations are given below.

Most alarm panel manufacturers will have the capability to configure a zone as a keyswitch and generally have at least one on-board programmable output that can be configured to activate on a number of different control state conditions. Reference the alarm panel installation manual for details on your specific installation.

Ademco/Honeywell Vista (General Concept)

56 program zone as type 77 80 Menu LED Outs
Program 17 and 18 zone type 78 and 79

DSC PowerSeries (General Concept)

Program zone as ‘22’ PGM Output ‘6’

DSC Alexor (General Concept)

Wiring: Y/Tx -> I/01 G/Rx -> I/02
6.2 k ohms resistor from + -> Y/Tx

Programming:

Section 009 - ‘05’/’22’
Section 013 - Enable 2 & Disable 1
Section 134 - Enable 14 (Press 9, then 6) This makes it normally closed.
Section 501 - Enable 3

GE NetworX (General Concept)

Location 25 Program zone as ‘11’ LED Status
Location 47 Segment 1: Enter 21
Location 47 Segment 2: Enter 0

Supported Panels

Honeywell

Panel

Revision

Digital Dialer

Full Interactive

GSM Emulator

Vista-10P

2.6+

Panel:
Vista-10P

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-10PSIA

4.0+

Panel:
Vista-10PSIA

Revision:
4.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-128BP

3.0+

Panel:
Vista-128BP

Revision:
3.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-128BPE

1.0+

Panel:
Vista-128BPE

Revision:
1.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-128FB

1.0+

Panel:
Vista-128FB

Revision:
1.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-128FBP

2.0+

Panel:
Vista-128FBP

Revision:
2.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-128FBPE

1.0+

Panel:
Vista-128FBPE

Revision:
1.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-128SIA

2008+

Panel:
Vista-128SIA

Revision:
2008+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-15

2+

Panel:
Vista-15

Revision:
2+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-15CN

2.6+

Panel:
Vista-15CN

Revision:
2.6+

Digital Dialer:

Full Interactive:

Vista-15P

2.6+

Panel:
Vista-15P

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-15PCN

2.6+

Panel:
Vista-15PCN

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-15PSIA

4.0+

Panel:
Vista-15PSIA

Revision:
4.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-20P

2.6+

Panel:
Vista-20P

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-20PCN

2.6+

Panel:
Vista-20PCN

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-20PI

5+

Panel:
Vista-20PI

Revision:
5+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-20PS

2.6+

Panel:
Vista-20PS

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-20PSIA

4.0+

Panel:
Vista-20PSIA

Revision:
4.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-21IP

1.0+

Panel:
Vista-21IP

Revision:
1.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-21IPSIA

1.0+

Panel:
Vista-21IPSIA

Revision:
1.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-32FB

1.0+

Panel:
Vista-32FB

Revision:
1.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

First Alert FA130

2.6+

Panel:
First Alert FA130

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

First Alert FA148

2.6+

Panel:
First Alert FA148

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

First Alert FA168

2.6+

Panel:
First Alert FA168

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

ADT Safewatch Pro 3000/3000EN

2.6+

Panel:
ADT Safewatch Pro 3000/3000EN

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

DSC (Digital Security Control)

Panel

Revision

Digital Dialer

Full Interactive

GSM Emulator

PC5010

Any

Panel:
PC5010

Revision:
Any

Digital Dialer:

Full Interactive:

GSM Emulator:

PC1616

4.13+

Panel:
PC1616

Revision:
4.13+

Digital Dialer:

Full Interactive:

GSM Emulator:

PC1832

4.13+

Panel:
PC1832

Revision:
4.13+

Digital Dialer:

Full Interactive:

GSM Emulator:

PC1864

4.13+

Panel:
PC1864

Revision:
4.13+

Digital Dialer:

Full Interactive:

GSM Emulator:

Alexor

All

Panel:
Alexor

Revision:
All

Digital Dialer:

Full Interactive:

GSM Emulator:

GE NetworX

Panel

Revision

Digital Dialer

Full Interactive

GSM Emulator

NX-4V2

V2+

Panel:
NX-4V2

Revision:
V2+

Digital Dialer:

Full Interactive:

GSM Emulator:

NX-6V2

V2+

Panel:
NX-6V2

Revision:
V2+

Digital Dialer:

Full Interactive:

GSM Emulator:

NX-8V2

V2+

Panel:
NX-8V2

Revision:
V2+

Digital Dialer:

Full Interactive:

GSM Emulator:

For non-supported panels: Bridge 12 VDC to “Y/TX” Terminal with any type of radial resistor with a value of 2.7k to 10k as a weak “pull up”.

Note: Any Control Panel NOT on this list is supported as long as it provides Tip & Ring and transmits Contact ID. If the panel has the ability to use a Dedicated Open Zone that acts as a Keyswitc h, you can Arm/Disarm from the Website or Mobile Phone.

Specifications

Radio

• Frequencies CDMA 1x

800 MHz/1900 MHz

Power

• Externally provided

12v DC

• Typical Current

130 mA

• Max Current

180 mA

Environmental

• Temperature Range

- 30° to +70° C (- 22° to +158° F)

• Humidity

0 to 95% non-condensing

Physical

• Height

7.05 inches

• Width

4.45 inches

• Depth

1.5 inches

Close