Toll Free: 866.896.2944

Product Manual

BAT LTE
SKU: IPD-BAT-LTE

LTE Cellular & Internet
Alarm Communicator

Technical Support Information

For Technical Support, call toll free: 866-896-2944
Monday - Friday 7a - 6:30p CST
techsupport@ipdatatel.com
ipdatatel.com
www.alarmdealer.com
setup.alarmdealer.com - Mobile Friendly

ipDatatel, LLC
13110 Southwest Freeway
Sugar Land, TX 77478
Toll Free: 866-896-2944

Quick Reference

Programming on GE Network:

Dev~ice 0

BAT LTE as Sole Communicator

Location 0

Enter the Phone Number

Location 0

Enter the Phone Number

Location 1

Enter Account Number

Location 1

Enter Account Number

Location 2

Enter ‘13’ for Contact ID

Location 2

Enter ‘13’ for Contact ID

Programming on Vista:

BAT LTE as Sole Communicator

*41

Enter Phone Number

*41

Enter Phone Number

*43

Enter Account Number

*43

Enter Account Number

*193

Enter 1, 0. Enable to turn on Address 20

*193

Enter 1, 0. Enable to turn on Address 20

*48

Enter 7,7 for Contact ID

*48

Enter 7,7 for Contact ID

Programming on DSC:

Section

BAT LTE as Sole Communicator

301

Enter Phone Number

301

Enter Phone Number

310

Enter Account Number

310

Enter Account Number

350

Enter ‘03’ for Contact ID

350

Enter ‘03’ for Contact ID

BAT LTE

Universal Dual-Path Internet & Cellular LTE Alarm Communicator

ipDatatel’s newest device, the BAT LTE, is a dual-path Internet & Cellular (LTE) alarm communicator offering redundant alarm
communications with industry-leading remote service capabilities when connected via keybus to supported Honeywell,
DSC and GE/Caddx panels.

Telco - Digital Dialer

The BAT LTE‘s signal collection expects Contact ID format from the digital dialer on the alarm panel. Most control panels
made in the last decade can perform this function. Wire the Telco side of the alarm control’s Tip & Ring to the Product’s Tip
& Ring.

Virtual Keypad Connection

The BAT LTE connects to most panels as a virtual keypad and allows the customer full virtual keypad access after they have
authenticated using their username and password you have assigned them in the pre- installation phase. This allows the
customer to use our SecureSmart mobile phone and web interfaces. Refer to wiring diagram for your specific panel. Panel
side of the virtual keypad connection will use various labels such as: Data in-Data out, YEL-GRN, or Data. This connects to
the G/RX, Y/TX connections on the Product.

🛑

Before installing any ipDatatel alarm communicator you must first be a registered dealer with ipDatatel and
you must also register your device using our Dealer Portal – AlarmDealer.com. Please reference ipDatatel’s
AlarmDealer.com Dealer User Guide for detailed information. www.ipdatatel.com/resources/software-apps/

Installing BAT LTE

Test your device

  • Power up your device using a 12-volt DC battery as a test with the back-up 12-volt battery from
    your alarm panel.
    • Connect the positive wire to Terminal 6-24 V on your device and then to the positive terminal on
      your panel battery.
    • Connect the negative wire to Terminal GND to the negative terminal on the panel battery.
    • Look for the green status light to verify that the unit is powering up.

Verify cellular signal strength

  • Good signal strength is indicated with the 4 green signal strength lights on the top right corner of
    the device board.
    • One or two lights, indicate a weak signal.
    • Three or four lights indicate a strong signal.
    • It’s recommended to keep a distance of twelve inches (12”) between the communicator and the alarm panel.
  • If cellular signal strength is good, mount the plastic enclosure with a screw.
  • If you have a weak cellular signal, move the device until an adequate signal strength is found.
    • Outer walls, higher up, often work best.

Connect the 6 wires from the device to the panel

  • Terminal T connects to the Tip connector on the Panel (This is used for Communication).
  • Terminal R connects to the Ring connector on the Panel (This is used for Communication).
  • Terminal 6-24 V connects to the Positive connector on the Panel (This powers your device).
  • Terminal GND connects to the Negative connector on the Panel (This powers your device).
  • Terminal Y In connects to the Yellow/Tx connector on the Panel (This is used for Interactive Services).
  • Terminal G In connects to the Green/Rx connector on the Panel (This is used for Interactive Services).

Program the panel to communicate alarm signals.

  • Enter the Central Station phone number and account number using the alarm panel keypad.
    • Make sure the panel is set to send in Contact ID mode.
    • Please reference the alarm panel’s guide for detailed panel programming information.

Transmit a test signal

  • Before wiring the Ethernet to the router enter the test signal code on the alarm keypad.

Connect Ethernet

  • Connect the Ethernet wire from the modem or router into the Ethernet port on the bottom right corner
    of the device.
    • This step is optional, but highly recommended to maximize performance while providing redundant
      communications

Activate the virtual keypad (follow these steps on the alarm panel keypad)

  • Vista panels - Enable Address 20 (Field 193) in panel programming.
  • DSC panels – No further programming is required.
  • GE panels - Enter & Exit programming at least 3 times to auto-enroll address 240.

Validate that your device is working correctly

  • Go to SetUp.AlarmDealer.com on your Smartphone or tablet.
  • Search by MAC ID, and click the Info tab to verify that your device is now online.
  • All signals received by the unit will be recorded on the customer’s event log within the
    AlarmDealer.com portal.
  • Please reference ipDatatel’s AlarmDealer.com Dealer User Guide for detailed information.
    www.ipdatatel.com/resources/software-apps/

Wiring & Programming for Popular Panels

The following pages are organized by Alarm Panel type. Wiring and programming instructions are given for:
  • Digital Security Control (DSC) Alarm Panels
    • Ademco & Honeywell Vista Alarm Panels
    • GE NetworX Alarm Panels

DSC Panel Wiring and Programming

DSC Panel Programming

  • Recommended Keybus with Tip & Ring
  • (Keyswitch alternative programming see Page 17)

See Supported Panels section on page 18. Perform the TELCO Programming if Tip & Ring is being used.

TELCO Programming:
General Concept Programming on DSC (BAT LTE as Sole Communicator):

Section

As Sole Communicator

Code Summarization

301

Enter a Receiver Number

Section:
301

As Sole Communicator:
Enter a Receiver Number

310

Enter Account Number

Section:
310

As Sole Communicator:
Enter Account Number

350

Enter ‘03’ to send Contact ID

Panel default is ‘04’, SIA

Section:
350

As Sole Communicator:
Enter ‘03’ to send Contact ID

Code Summarization:
Panel default is ‘04’, SIA

Note: Ensure All Report Codes are in, and signals can be sent.

DSC PC-Link connection

PC-Link connection should only be used when the communicator is being installed as a back-up or uploading/downloading
using DLS V. Remote downloader functionality requires ipDatatel’s uDownloader software.

PC-Link Programming:

(Only needed if sending signals via PC-Link)
DSC Programming for Communications - GSM Emulation: If GSM is used, it must be in dialer capture mode.

Sec

BAT LTE as Sole Communicator

BAT LTE as Fail over w/Add’l Communication Device

BAT LTE as Dual
Reporting w/Add’l
Communication
Device

Code Summarization

015

Disable Option 7

If GSM: Disable Option 7 If Phone Line, Enable Option 7

If GSM: Disable Option 7 If Phone Line, Enable Option 7

Option 7 turns on/off telephone line supervision.

Section:
015

BAT LTE as Sole Communicator:
Disable Option 7

BAT LTE as Fail over w/Add'l Communication Device:
If GSM: Disable Option 7 If Phone Line, Enable Option 7

BAT LTE as Dual Reporting w/Add’l Communication Device
If GSM: Disable Option 7 If Phone Line, Enable Option 7

Code Summarization:
Option 7 turns on/off telephone line supervision.

167

Set ‘060’ Seconds

Set ‘060’ Seconds

Set ‘060’ Seconds

Option 7 turns on/off
telephone line supervision.

Section:
167

BAT LTE as Sole Communicator:
Set ‘060’ Seconds

BAT LTE as Fail over w/Add'l Communication Device:
Set ‘060’ Seconds

BAT LTE as Dual Reporting w/Add’l Communication Device:
Set ‘060’ Seconds

Code Summarization:
Option 7 turns on/off telephone line supervision.

301

Set ‘CAAF’

Set ‘CAAF’

Set ‘CAAF’

‘CAAF’ has to be set for the
panel to send signals to the
PC- Link

Section:
301

BAT LTE as Sole Communicator:
Set ‘CAAF’

BAT LTE as Fail over w/Add'l Communication Device:
Set ‘CAAF’

BAT LTE as Dual Reporting w/Add’l Communication Device:
Set ‘CAAF’

Code Summarization:
‘CAAF’ has to be set for the panel to send signals to the PC- Link

302

N/A

N/A

Set ‘Central Station Receiver #’

Second telephone number
goes here.

Section:
302

BAT LTE as Sole Communicator:
N/A

BAT LTE as Fail over w/Add'l Communication Device:
N/A

BAT LTE as Dual Reporting w/Add’l Communication Device:
Set ‘Central Station Receiver #’

Code Summarization:
Second telephone number goes here.

303

N/A

Set ‘Central Station Receiver #’

Set ‘Central Station Receiver #’

This section is the telephone
backup of section 301.

Section:
303

BAT LTE as Sole Communicator:
N/A

BAT LTE as Fail over w/Add'l Communication Device:
Set ‘Central Station Receiver #’

BAT LTE as Dual Reporting w/Add’l Communication Device:
Set ‘Central Station Receiver #’

Code Summarization:
This section is the telephone backup of section 301.

350

Set ‘04’/‘04’

Set ‘04’/’03 for Contact ID, 04 for SIA FSK’ **

Set ‘04’/’03 for Contact ID, 04 for SAI FSK’ **

Format sent as either contact ID (03), or SIA FSK (04). The PC-Link/BAT LTE can ONLY receive signals via SIA FSK (04).

Section:
350

BAT LTE as Sole Communicator:
Set ‘04’/‘04’

BAT LTE as Fail over w/Add'l Communication Device:
Set ‘04’/’03 for Contact ID, 04
for SIA FSK’ **

BAT LTE as Dual Reporting w/Add’l Communication Device:
Set ‘04’/’03 for
Contact ID, 04 for SAI FSK’ **

Code Summarization:
Format sent as either contact ID (03), or SIA FSK (04). The PC-Link/BAT LTE can ONLY receive signals via SIA FSK (04).

351

Enable Option 1

Enable Option 1, 5

Enable Option 1, 2, 5

Options to turn on/off alarm/restore for telephone 1 (option 1), telephone 2 (option 2), and alternate communications (option 5).

Section:
351

BAT LTE as Sole Communicator:
Enable Option 1

BAT LTE as Fail over w/Add'l Communication Device:
Enable Option 1, 5

BAT LTE as Dual Reporting w/Add’l Communication Device:
Enable Option 1, 2, 5

Code Summarization:
Options to turn on/off alarm/restore for telephone 1 (option 1), telephone 2 (option 2), and alternate communications (option 5).

359

Enable Option 1

Enable Option 1, 5

Enable Option 1, 2, 5

Options to turn on/off
tamper/restore for telephone
1 (option 1), telephone 2
(option 2), and alternate
communications (option 5).

Section:
359

BAT LTE as Sole Communicator:
Enable Option 1

BAT LTE as Fail over w/Add'l Communication Device:
Enable Option 1, 5

BAT LTE as Dual Reporting w/Add’l Communication Device:
Enable Option 1, 2, 5

Code Summarization:
Options to turn on/off tamper/restore for telephone 1 (option 1), telephone 2 (option 2), and alternate communications (option 5).

367

Enable Option 1

Enable Option 1, 5

Enable Option 1, 2, 5

Options to turn on/off
tamper/restore for telephone
1 (option 1), telephone 2
(option 2), and alternate
communications (option 5).

Section:
367

BAT LTE as Sole Communicator:
Enable Option 1

BAT LTE as Fail over w/Add'l Communication Device:
Enable Option 1, 5

BAT LTE as Dual Reporting w/Add’l Communication Device:
Enable Option 1, 2, 5

Code Summarization:
Options to turn on/off tamper/restore for telephone 1 (option 1), telephone 2 (option 2), and alternate communications (option 5).

375

Enable Option 1

Enable Option 1, 5

Enable Option 1, 2, 5

Options to turn on/off
tamper/restore for telephone
1 (option 1), telephone 2
(option 2), and alternate
communications (option 5).

Section:
375

BAT LTE as Sole Communicator:
Enable Option 1

BAT LTE as Fail over w/Add'l Communication Device:
Enable Option 1, 5

BAT LTE as Dual Reporting w/Add’l Communication Device:
Enable Option 1, 2, 5

Code Summarization:
Options to turn on/off tamper/restore for telephone 1 (option 1), telephone 2 (option 2), and alternate communications (option 5).

376

Enable Option 1

Enable Option 1, 5

Enable Option 1, 2, 5

Options to turn on/off
tamper/restore for telephone
1 (option 1), telephone 2
(option 2), and alternate
communications (option 5).

Section:
376

BAT LTE as Sole Communicator:
Enable Option 1

BAT LTE as Fail over w/Add'l Communication Device:
Enable Option 1, 5

BAT LTE as Dual Reporting w/Add’l Communication Device:
Enable Option 1, 2, 5

Code Summarization:
Options to turn on/off tamper/restore for telephone 1 (option 1), telephone 2 (option 2), and alternate communications (option 5).

380

Enable Option 1

Enable Option 1, 5

Enable Option 1, 5

Option 1 turns on/off
communications. Option
5 turns on/off 3rd phone
number.

Section:
380

BAT LTE as Sole Communicator:
Enable Option 1

BAT LTE as Fail over w/Add'l Communication Device:
Enable Option 1, 5

BAT LTE as Dual Reporting w/Add’l Communication Device:
Enable Option 1, 5

Code Summarization:
Option 1 turns on/off communications. Option 5 turns on/off 3rd phone number.

381

Disable Option 3, Enable Option 5

Disable Option 3, Enable Option 5, 6

Disable Option 3, Enable Option 5, 6

Option 3 turns on/off code
reporting. Options 5 & 6
turns on/off communication
with phone lines 1/3 & 2
respectively.

Section:
381

BAT LTE as Sole Communicator:
Disable Option
3, Enable Option 5

BAT LTE as Fail over w/Add'l Communication Device:
Disable Option 3, Enable Option 5, 6

BAT LTE as Dual Reporting w/Add’l Communication Device:
Disable Option 3, Enable Option 5, 6

Code Summarization:
Option 3 turns on/off code reporting. Options 5 & 6 turns on/off communication with phone lines 1/3 & 2 respectively.

382

Enable Option 5

Enable Option 5

Enable Option 5

Option 5 enables/disables
T-Link/PC-Link.

Section:
382

BAT LTE as Sole Communicator:
Enable Option 5

BAT LTE as Fail over w/Add'l Communication Device:
Enable Option 5

BAT LTE as Dual Reporting w/Add’l Communication Device:
Enable Option 5

Code Summarization:
Option 5 enables/disables T-Link/PC-Link.

389

Enable Option 5

Enable Option 5

Enable Option 5

The time it will take to periodically check for faults on the T-Link/PC- Link.

Section:
389

BAT LTE as Sole Communicator:
Enable Option 5

BAT LTE as Fail over w/Add'l Communication Device:
Enable Option 5

BAT LTE as Dual Reporting w/Add’l Communication Device:
Enable Option 5

Code Summarization:
The time it will take to periodically check for faults on the T-Link/PC- Link.

Honeywell Vista Panel Wiring and Programming

Honeywell Vista Panel Programming

  • Recommended Keybus with Tip & Ring
  • (Keyswitch alternative programming see Page 17)

See supported panels section on page 18. Perform the TELCO programming if Tip & Ring is being used. If for whatever
reason you cannot use Tip & Ring to send signals then you can perform ecp bus programming. Otherwise, ALWAYS use TELCO programming.

TELCO Programming:

Programming on Vista (BAT LTE as Sole Communicator):

Section

BAT LTE as Sole Communicator

Code Summarization

*41

Enter Phone Number

Section:
*41

BAT LTE as Sole Communicator:
Enter Phone Number

*43

Enter Account Number

Section:
*43

BAT LTE as Sole Communicator:
Enter Account Number

*49

Enter 5

For All Communications to BAT LTE

Section:
*49

BAT LTE as Sole Communicator:
Enter 5

Code Summarization:
For All Communications to BAT LTE

*54

Enter 0

No Delay Between Communicators

Section:
*54

BAT LTE as Sole Communicator:
Enter 0

Code Summarization:
No Delay Between Communicators

*55

Enter 0

Phone Line Communicates First

Section:
*55

BAT LTE as Sole Communicator:
Enter 0

Code Summarization:
Phone Line Communicates First

*65 & *66

Enter 1 till beep

If you want Opening/Closing Reports

Section:
*65 & *66

BAT LTE as Sole Communicator:
Enter 1 till beep

Code Summarization:
If you want Opening/Closing Reports

*193

Enter 1, 0

Enable to turn on Address 20

Section:
*193

BAT LTE as Sole Communicator:
Enter 1, 0

Code Summarization:
Enable to turn on Address 20

*48

7,7

If you want Opening/Closing Reports

Section:
*48

BAT LTE as Sole Communicator:
7,7

Code Summarization:
If you want Opening/Closing Reports

*47

Enter 1

Section:
*47

BAT LTE as Sole Communicator:
Enter 1

ECP Bus Programming:

ONLY NEEDED IF USING ECP TO SEND SIGNALS AND NOT TIP/RING
Vista Programming for Communications - GSM Emulation:

Sec

BAT LTE as
Sole
Communicator

BAT LTE in use with another Communication Device for Failover

For Dual Reporting

Code Summarization

*29

Enter 1

Enter 1

Enter 1

This enables GSM. The BAT LTE Emulates a GSM.

Section:
*29

BAT LTE as Sole Communicator:
Enter 1

BAT LTE in use with another Communication Device for Failover:
Enter 1

For Dual Reporting:
Enter 1

Code Summarization
This enables GSM. The BAT LTE Emulates a GSM.

*42

N/A

Enter Central Station Receiver Number

Enter Central Station Receiver Number

Secondary Phone Number

Section:
*42

BAT LTE as Sole Communicator:
N/A

BAT LTE in use with another Communication Device for Failover:
Enter Central Station Receiver Number

For Dual Reporting:
Enter Central Station Receiver Number

Code Summarization:
Secondary Phone Number

*43

Enter Account Number

Enter Account Number

Enter Account Number

This is the central station account number

Section:
*43

BAT LTE as Sole Communicator:
Enter Account Number

BAT LTE in use with another Communication Device for Failover:
Enter Account
Number

For Dual Reporting:
Enter Account Number

Code Summarization:
This is the central station account number

*49

Enter 5

Please refer to panel manual for your particular application
requirements

Please refer to panel manual for your particular application requirements

Dual Reporting; Setting to 5 sends all reporting to both primary and secondary.

Section:
*49

BAT LTE as Sole Communicator:
Enter 5

BAT LTE in use with another Communication Device for Failover:
Please refer to panel manual for your particular application
requirements

For Dual Reporting:
Please refer to panel manual for your particular application requirements

Code Summarization:
Dual Reporting; Setting to 5 sends all reporting to both primary and secondary.

*54

Enter 0

Enter 2

Enter 0

The time it takes for the communicator to switch from primary to secondary.

Section:
*54

BAT LTE as Sole Communicator:
Enter 0

BAT LTE in use with another Communication Device for Failover:
Enter 2

For Dual Reporting:
Enter 0

Code Summarization:
The time it takes for the
communicator to switch
from primary to secondary.

*55

Enter 1

Enter 1

Enter 1 (BAT LTE is Primary Communicator)

Setting to 1 gives signal priority to GSM (BAT LTE).

Section:
*55

BAT LTE as Sole Communicator:
Enter 1

BAT LTE in use with another Communication Device for Failover:
Enter 1

For Dual Reporting:
Enter 1 (BAT LTE is Primary Communicator)

Code Summarization:
Setting to 1 gives signal priority to GSM (BAT LTE).

*65

Enter 1

Enter 1 till beep

Enter 1

Report Code for Openings.

Section:
*65

BAT LTE as Sole Communicator:
Enter 1

BAT LTE in use with another Communication Device for Failover:
Enter 1 till beep

For Dual Reporting:
Enter 1

Code Summarization:
Report Code for Openings.

*66

Enter 1, 1

Enter 1, 1 till beep

Enter 1, 1

Report Code for Arming in
Away and Stay.

Section:
*66

BAT LTE as Sole Communicator:
Enter 1, 1

BAT LTE in use with another Communication Device for Failover:
Enter 1, 1 till beep

For Dual Reporting:
Enter 1, 1

Code Summarization:
Report Code for Arming in Away and Stay.

*193

Enter 1, 0

Enter 1, 0

Enter 1, 0

1 turns on/off keypad address. 0 sets sound to beep.

Section:
*193

BAT LTE as Sole Communicator:
Enter 1, 0

BAT LTE in use with another Communication Device for Failover:
Enter 1, 0

For Dual Reporting:
Enter 1, 0

Code Summarization:
1 turns on/off keypad address. 0 sets sound to
beep.

*48

7,7

1 turns on/off keypad address. 0 sets sound to beep.

Section:
*48

BAT LTE as Sole Communicator:
7,7

Code Summarization:
1 turns on/off keypad address. 0 sets sound to
beep.

See Supported Panels section on pages 18-19 to verify your panel’s revision number and GSM emulation programming.

GE Panel Wiring and Programming

GE Panel Programming

  • Recommended Keybus with Tip & Ring
  • (Keyswitch alternative programming see Page 17)

TELCO Programming:

General Concept Programming on GE NetworX:

Section

BAT LTE as Sole Communicator

Code Summarization

Device 0, Location 0

Enter the Phone Number

Section
Device 0, Location 0

BAT LTE as Sole Communicator:
Enter the Phone Number

Device 0, Location 1

Enter Account Number

Section
Device 0, Location 1

BAT LTE as Sole Communicator:
Enter Account Number

Device 0, Location 2

Enter ‘13’

Enter ‘13’

Section
Device 0, Location 2

BAT LTE as Sole Communicator:
Enter ‘13’

Code Summarization
Enter ‘13’

Generic Alarm Panel Wiring and Programming

Generic Alarm Panel Programming

  • Program the panel Phone Number into the panel
  • Program the Customer Account Number into the panel
  • Program Reporting codes into the panel
  • Program panel to transmit in 10 digit CID format

Generic Keyswitch Wiring and Programming

For basic keyswitch interactive services with the BAT LTE, the following alarm panel wiring is needed.

  • A programmable output on the alarm panel will be used to signal to the Product (Y/Tx terminal) that the panel has entered Arm/Disarmed State.
  • The Z1 output on the Product will be used as a key switch connecting to a ‘zone’ terminal on the alarm panel.

*Panel zone resistor placed on Terminal 3 to 5 to determine correct arm and disarm state.

Generic Keyswitch Programming

Keyswitch state programming examples for Ademco, Digital Security Controls, and GE NetworX for Keyswitch and panel state program output operations are given below.

Most alarm panel manufacturers will have the capability to configure a zone as a keyswitch and generally have at least one on-board programmable output that can be configured to activate on a number of different control state conditions.

Reference the alarm panel installation manual for details on your specific installation.

Ademco/Honeywell Vista (General Concept)

  • 56 program zone as type 77
    80 Menu LED Outs
  • Program 17 and 18 zone type 78 and 79

DSC PowerSeries (General Concept)

  • Program zone as ‘22’ PGM Output ‘6’

DSC Alexor (General Concept)

  • Wiring: Y/Tx -> I/01 Terminal 13 -> I/02
  • 6.2k ohms resistor from + positive -> Y/Tx

Programming:

  • Section 009 - ‘05’/’22’
  • Section 013 - Enable 2 & Disable 1
  • Section 134 - Enable 14 (Press 9, then 6) This makes it normally closed.
  • Section 501 - Enable 3

GE NetworX (General Concept)

  • Location 25 Program zone as ‘11’ LED Status
  • Location 47 Segment 1: Enter 21
  • Location 47 Segment 2: Enter 0

Supported Panels

Honeywell

Panel

Revision

Digital Dialer

Full Interactive

GSM Emulator

Vista-10P

2.6+

Panel:
Vista-10P

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-10PSIA

4.0+

Panel:
Vista-10PSIA

Revision:
4.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-128BP

3.0+

Panel:
Vista-128BP

Revision:
3.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-128BPE

1.0+

Panel:
Vista-128BPE

Revision:
1.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-128FB

1.0+

Panel:
Vista-128FB

Revision:
1.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-128FBP

2.0+

Panel:
Vista-128FBP

Revision:
2.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-128FBPE

1.0+

Panel:
Vista-128FBPE

Revision:
1.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-128SIA

2008+

Panel:
Vista-128SIA

Revision:
2008+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-15

2+

Panel:
Vista-15

Revision:
2+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-15CN

2.6+

Panel:
Vista-15CN

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-15P

2.6+

Panel:
Vista-15P

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-15PCN

2.6+

Panel:
Vista-15PCN

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-15PSIA

4.0+

Panel:
Vista-15PSIA

Revision:
4.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-20P

2.6+

Panel:
Vista-20P

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-20PCN

2.6+

Panel:
Vista-20PCN

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-20PI

5+

Panel:
Vista-20PI

Revision:
5+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-20PS

2.6+

Panel:
Vista-20PS

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-20PSIA

4.0+

Panel:
Vista-20PSIA

Revision:
4.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-21IP

1.0+

Panel:
Vista-21IP

Revision:
1.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-21IPSIA

1.0+

Panel:
Vista-21IPSIA

Revision:
1.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

Vista-32FB

1.0+

Panel:
Vista-32FB

Revision:
1.0+

Digital Dialer:

Full Interactive:

GSM Emulator:

First Alert FA130

2.6+

Panel:
First Alert FA130

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

First Alert FA148

2.6+

Panel:
First Alert FA148

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

First Alert FA168

2.6+

Panel:
First Alert FA168

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

ADT Safewatch Pro 3000/3000EN

2.6+

Panel:
ADT Safewatch Pro 3000/3000EN

Revision:
2.6+

Digital Dialer:

Full Interactive:

GSM Emulator:

DSC (Digital Security Control)

Panel

Revision

Digital Dialer

Full Interactive

GSM Emulator

PC5010

Any

Panel:
PC5010

Revision:
Any

Digital Dialer:

Full Interactive:

GSM Emulator:

PC1616

4.13+

Panel:
PC1616

Revision:
4.13+

Digital Dialer:

Full Interactive:

GSM Emulator:

PC1832

4.13+

Panel:
PC1832

Revision:
4.13+

Digital Dialer:

Full Interactive:

GSM Emulator:

PC1864

4.13+

Panel:
PC1864

Revision:
4.13+

Digital Dialer:

Full Interactive:

GSM Emulator:

Alexor

ALL

Panel:
Alexor

Revision:
ALL

Digital Dialer:

Full Interactive:

GSM Emulator:

GE NetworX

Panel

Revision

Digital Dialer

Full Interactive

GSM Emulator

NX-4V2

V2+

Panel:
NX-4V2

Revision:
V2+

Digital Dialer:

Full Interactive:

GSM Emulator:

NX-6V2

V2+

Panel:
NX-6V2

Revision:
V2+

Digital Dialer:

Full Interactive:

GSM Emulator:

NX-8V2

V2+

Panel:
NX-8V2

Revision:
V2+

Digital Dialer:

Full Interactive:

GSM Emulator:

For non-supported panels: Bridge 12 VDC to “Y/TX” Terminal with any type of radial resistor with a value of 2.0k to 10k as a weak “pull up”.

Note: Any Control Panel NOT on this list is supported as long as it provides Tip & Ring and transmits Contact ID. If the panel
has the ability to use a Dedicated Open Zone that acts as a Keyswitch, you can Arm/Disarm from the Website or Mobile
Phone.

Specifications

Radio

• Frequencies LTE 1x

1900MHz, 1700MHz, 700MHz

Power

• Externally provided

12v DC

• Typical Current

130 mA

• Max Current

180 mA

Environmental

• Temperature Range

- 30° to +70° C (- 22° to +158° F)

• Humidity

0 to 95% non-condensing

Physical

• Height

7.05 inches

• Width

7.05 inches

• Depth

1.5 inches

Close